Dell Inspiron 5680 Page 47 Service Manual Download

Page: 47 / 130

Replacing the front-panel light

board

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before

working inside your computer

. After working inside your computer, follow

the instructions in

After working inside your computer

. For more safety best

practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Procedure

Align the front panel light-board cable to the slot on the chassis.

Replace the screw (M3x5) that secures the front panel light-board to the
chassis.

Connect the front panel light-board cable to the logo board.

Route the cables through the routing guides on the chassis and connect the
front panel light-board cable to the system board.

Place the computer in an upright position.

Post-requisites

Replace the

front cover

Replace the

right-side cover

Summary of Contents for Inspiron 5680



































































































































Search results

Summary of Contents for Inspiron 5680

Reviews:

Related manuals for Inspiron 5680

Brands by name

Popular brands

Dell Inspiron 5680, Service Manual

Search results

Summary of Contents for Inspiron 5680

Reviews:

Related manuals for Inspiron 5680

Brands by name

Popular brands