Dell Inspiron 3800 System Reference Manual Download Page 149

Page: 149 / 161

Power Sources: Dell Inspiron 3800 System Reference

Lift and rotate the top of the LCD panel out of the top cover.

Disconnect the ZIF connector and the display-assembly interface cable connector (see

Figure 4

Lift the LCD panel out of the top cover.

NOTES: Remove and replace the LCD panel as a complete assembly.

Use a magnetic screwdriver to reassemble the LCD panel in the display. Secure the right side first.

Removing the 14.1-Inch LCD Flex Cable

Remove the 4-mm screw securing the metal cable clip to the left hinge of the display-assembly top cover (see

Figure

Remove the cable out from under the plastic strain-relief retainer located on the bottom of the display-assembly hinge
cover.

Remove the clip from the bottom of the hinge cover located at the bottom of the display assembly.

Pry the hinge-cover assembly apart from the display assembly, allowing just enough space for the flex cable to pass
through the opening.

Slide the cable through the opening.

12.1-Inch Display LCD Panel

Figure 15. 12.1-Inch Display Assembly

Display
assembly
bezel

Back-light
plug

Latch

Inverter

ZIF
connector

3-mm screws
(3)

file:///F|/Service%20Manuals/Dell/Inspiron/3800/r_r.htm (18 of 30) [2/28/2004 6:59:08 AM]

Summary of Contents for Inspiron 3800


































































































































































Search results

Summary of Contents for Inspiron 3800

Reviews:

Related manuals for Inspiron 3800

Brands by name

Popular brands

Dell Inspiron 3800, System Reference Manual

Search results

Summary of Contents for Inspiron 3800

Reviews:

Related manuals for Inspiron 3800

Brands by name

Popular brands