manualshive.com logo in svg

Dell Inspiron 3670, Service Manual, Page: 31 / 76

Share
Download
Dell Inspiron 3670 Service Manual Download Page 31

Replacing the wireless card

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer and follow the 

steps in 

Before working inside your computer

. After working inside your computer, follow the instructions in 

After working inside 

your computer

. For more safety best practices, see the Regulatory Compliance home page at 

www.dell.com/

regulatory_compliance

.

 

Topics:

•

Procedure

•

Post-requisites

Procedure

1 

Connect the antenna cables to the wireless card.

2 

Slide the wireless-card bracket on the wireless card, and align the screw hole on the bracket with the screw hole on the wireless card.

3 

Align the notch on the wireless card with the tab on the wireless-card slot, then slide the wireless card at an angle into the wireless-
card slot.

4 

Replace the screw (M2x3.5) that secures the wireless card to the system board.

Post-requisites

Replace the 

computer cover

.

17

Replacing the wireless card

31

Summary of Contents for Inspiron 3670













































































Reviews:

No comments