manualshive.com logo in svg

Dell Inspiron 3670, Service Manual, Page: 26 / 76

Share
Download
Dell Inspiron 3670 Service Manual Download Page 26

Replacing the graphics card

WARNING: 

Before working inside your computer, read the safety information that shipped with your computer and follow the 

steps in 

Before working inside your computer

. After working inside your computer, follow the instructions in 

After working inside 

your computer

. For more safety best practices, see the Regulatory Compliance home page at 

www.dell.com/

regulatory_compliance

.

 

Topics:

•

Procedure

•

Post-requisites

Procedure

1 

Ensure the securing tab on the system board is pushed away from the graphics-card slot.

2 

Align the notch on the graphics card with the tab on the graphics card slot, and then press down firmly until the graphics card snaps 
into place.

NOTE: 

The securing tab will move to a closed position when the graphics card is replaced correctly. Remove the graphics 

card and repeat the procedure if the securing tab does not close.

3 

Rotate the card-retention bracket and align the screw hole on the card-retention bracket with the screw hole on the chassis.

4 

Replace the screw (#6-32x6.35) that secures the card-retention bracket to the chassis.

Post-requisites

Replace the 

computer cover

.

13

26

Replacing the graphics card

Summary of Contents for Inspiron 3670













































































Reviews:

No comments