Dell Inspiron 3470 Service Manual Download Page 77

Page: 77 / 82

Post-requisites

Replace the

computer cover

Clearing CMOS Settings

WARNING:

Before working inside your computer, read the safety information that shipped with your computer and follow the

steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside

your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Prerequisites

Remove the

computer cover

Procedure

Locate the CMOS jumper (CMCL R2) on the system board.

NOTE:

For more information on the location of the jumper, see “

system-board components

”.

Remove the jumper plug from the password jumper-pins (PSWD) and connect it to the CMOS jumper-pins.

Wait for 5 seconds, and then replace the jumper plug to its original location.

System and setup password

Summary of Contents for Inspiron 3470



















































































Search results

Summary of Contents for Inspiron 3470

Reviews:

Related manuals for Inspiron 3470

Brands by name

Popular brands

Dell Inspiron 3470, Service Manual

Search results

Summary of Contents for Inspiron 3470

Reviews:

Related manuals for Inspiron 3470

Brands by name

Popular brands