manualshive.com logo in svg

Dell Inspiron 16 Plus 7620, Service Manual, Page: 31 / 69

Share
Download
Dell Inspiron 16 Plus 7620 Service Manual Download Page 31

Steps

1. Align the screw holes of the right fan with the screw holes on the palm-rest and keyboard assembly.
2. Replace the two screws (M2x5) that secure the right fan to the palm-rest and keyboard assembly.
3. Connect the right-fan cable to the system board.
4. Adhere the Mylar back over the right-fan cable.
5. Adhere the Mylar back in place over the system board.

Next steps

1. Install the 

base cover

.

2. Follow the procedure in 

After working inside your computer

.

Heat sink

Removing the heat sink

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

NOTE:

 Ensure that your computer is in Service Mode. For more information see, step 6 in 

Before working inside your

computer

.

2. Remove the 

base cover

.

About this task

NOTE:

 The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

The following image(s) indicate the location of the heat sink and provides a visual representation of the removal procedure.

Removing and installing components

31

Summary of Contents for Inspiron 16 Plus 7620






































































Reviews:

No comments