background image

Removing 

the 

Coin-Cell 

Battery  |  

51

Removing the Coin-Cell Battery

 

WARNING:  Before working inside your computer, read the safety information 
that shipped with your computer and follow the steps in "Before You Begin" on 
page 7. After working inside your computer, follow the instructions in "After 
Working Inside Your Computer" on page 9. For additional safety best practices 
information, see the Regulatory Compliance Homepage at 
dell.com/regulatory_compliance.

 

WARNING:  The coin-cell battery may explode if installed incorrectly. 
Replace the coin-cell battery only with the same or equivalent type. Discard used 
coin-cell batteries according to the manufacturer’s instructions.

 

CAUTION: Removing the coin-cell battery resets the BIOS settings to default. It is 
recommended that you note the BIOS settings before removing the coin-cell 
battery.

Prerequisites

1

Remove the battery. See "Removing the Battery" on page 11.

2

Follow the instructions from step 1 to step 2 in "Removing the Memory Module(s)" 
on page 15.

3

Remove the hard-drive assembly. See "Removing the Hard-Drive Assembly" on 
page 23.

4

Remove the optical-drive assembly. See "Removing the Optical-Drive Assembly" on 
page 19.

5

Remove the keyboard. See "Removing the Keyboard" on page 27.

6

Remove the palm-rest. See "Removing the Palm-Rest" on page 31.

7

Remove the system board. See "Removing the System Board" on page 45.

OM_Book.book  Page 51  Tuesday, November 20, 2012  12:43 PM

Summary of Contents for Inspiron 15 3521































































































Reviews: