Dell Inspiron 13 5000 Series 2-in-1 Service Manual Download Page 60

Page: 60 / 139

Removing the heat sink

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before working inside your computer

. After working inside your

computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory

Compliance home page at

www.dell.com/regulatory_compliance

WARNING: The heat sink may become hot during normal operation.
Allow sufficient time for the heat sink to cool before you touch it.

CAUTION: For maximum cooling of the processor, do not touch the

heat transfer areas on the heat sink. The oils in your skin can reduce

the heat transfer capability of the thermal grease.

Prerequisites

Remove the

base cover

Remove the

battery

Procedure

In sequential order (as indicated on the heat sink), loosen the captive

screws that secure the heat sink to the system board.

Summary of Contents for Inspiron 13 5000 Series 2-in-1












































































































































Search results

Summary of Contents for Inspiron 13 5000 Series 2-in-1

Reviews:

Related manuals for Inspiron 13 5000 Series 2-in-1

Brands by name

Popular brands

Dell Inspiron 13 5000 Series 2-in-1, Service Manual

Search results

Summary of Contents for Inspiron 13 5000 Series 2-in-1

Reviews:

Related manuals for Inspiron 13 5000 Series 2-in-1

Brands by name

Popular brands