Dell G5 15 Service Manual Download Page 84

Page: 84 / 112

Removing the display panel

WARNING:

Before working inside your computer, read the safety information that shipped with your computer and follow the

steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside

your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Topics:

•

Prerequisites

•

Procedure

Prerequisites

Remove the

Remove the

Remove the

Remove the

Follow the procedure from step 1 to step 17 in

Removing the computer base

Remove the

display assembly

Remove the

display bezel

Procedure

Remove the four screws (M2x2.5) that secure the display panel to the display back-cover.

Gently lift the display panel and turn it over.

Peel off the tape that secures the display cable to the display panel.

Open the latch and disconnect the display cable from the display panel.

Lift the display panel away from the display back-cover.

Removing the display panel

Summary of Contents for G5 15

















































































































Search results

Summary of Contents for G5 15

Reviews:

Related manuals for G5 15

Brands by name

Popular brands

Dell G5 15, Service Manual

Search results

Summary of Contents for G5 15

Reviews:

Related manuals for G5 15

Brands by name

Popular brands