Dell G5 15 Service Manual Download Page 28

Page: 28 / 112

Replacing the wireless card

WARNING:

Before working inside your computer, read the safety information that shipped with your computer and follow the

steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside

your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Topics:

•

Procedure

•

Post-requisites

Procedure

CAUTION:

To avoid damage to the wireless card, do not place any cables under it.

Align the notch on the wireless card with the tab on the wireless-card slot and slide the wireless card at an angle into the wireless-card
slot.

Connect the antenna cables to the wireless card.
The following table provides the antenna-cable color scheme for the wireless card supported by your computer.

Table 2. Antenna-cable color scheme

Connectors on the wireless card

Antenna-cable color

Main (white triangle)

White

Auxiliary (black triangle)

Black

Align the screw hole on the wireless-card bracket with the screw hole on the wireless card and the system board.

Replace the screw (M2x3) that secures the wireless-card bracket to the wireless card and system board.

Replacing the wireless card

Summary of Contents for G5 15

















































































































Search results

Summary of Contents for G5 15

Reviews:

Related manuals for G5 15

Brands by name

Popular brands

Dell G5 15, Service Manual

Search results

Summary of Contents for G5 15

Reviews:

Related manuals for G5 15

Brands by name

Popular brands