manualshive.com logo in svg

Dell G16 7620, Service Manual, Page: 53 / 79

Share
Download
Dell G16 7620 Service Manual Download Page 53

Installing the USB board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the USB board and provides a visual representation of the installation procedure.

Steps

1. Slide the USB board into the M.2 card slot on the system board and align the screw holes on the USB board to the screw

holes on the system board.

2. Replace the two screws (M2x4) that secure the USB board to the system board.
3. Turn the system-board assembly over.

Next steps

1. Install the 

system board

.

2. Install the 

wireless card

.

3. Install the 

solid-state drive

.

4. Install the 

rear cover

.

5. Install the 

battery

.

6. Install the 

base cover

.

7. Follow the procedure in 

After working inside your computer

.

Ethernet and audio board

Removing the ethernet and audio board

Prerequisites

Removing and installing components

53

Summary of Contents for G16 7620
















































































Reviews:

No comments