Dell G16 7620 Service Manual Download Page 41

Page: 41 / 79

Installing the system board (NVIDIA GeForce RTX 3060/3070/3070
Ti graphics card)

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

NOTE:

Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program.

Make the appropriate changes again after you replace the system board.

NOTE:

This procedure only applies to computers shipped with a NVIDIA GeForce 3060/3070/3070 Ti graphics card.

About this task

The following image indicates the connectors on your system board.

1. Display cable
2. DDS (Dynamic Display Switch) cable
3. Speaker cable
4. Right-fan cable
5. Power-adapter port cable
6. Touchpad cable
7. Keyboard-controller board cable
8. Left-fan cable
9. Power-button cable

The following image indicates the location of the system board and provides a visual representation of the installation procedure.

Removing and installing components

Summary of Contents for G16 7620
















































































Search results

Summary of Contents for G16 7620

Reviews:

Dell G16 7620, Service Manual, Page: 41 / 79

Search results

Summary of Contents for G16 7620

Reviews: