Dell FS7500 Installation And Setup Download

Page: 15 / 88

EqualLogic FS7500 Installation and Setup

1 Before You Begin

Figure 5: FS7500 Controller Back Panel

Figure 6: FS7500 Controller Back Panel Components

Number Component

Internal network interfaces

SAN network interfaces

C14 power connector (to AC power source)

Power supply status LED

IPMI port

Video port

USB port (to external keyboard)

USB port (to BPS)

Client network interfaces

System power-on status LED

C14 power connector (to BPS)

FS7500 BPS Front and Back Panels

Figure 7

and

Figure 8

show the front panels and the back panel of an FS7500 Backup Power Supply with both

power modules installed, and the BPS bezel removed.

Each power module has a front cover. The power modules contain the batteries.

Figure 7: FS7500 BPS Front Panel

Summary of Contents for FS7500

























































































Search results

Summary of Contents for FS7500

Reviews:

Related manuals for FS7500

Brands by name

Popular brands

Dell FS7500, Installation And Setup

Search results

Summary of Contents for FS7500

Reviews:

Related manuals for FS7500

Brands by name

Popular brands