manualshive.com logo in svg

Dell EMC PowerEdge T440, Installation And Service Manual

Share
Download
Dell EMC PowerEdge T440 Installation And Service Manual Download Page 148

•

Restore data from a previously created 

Hardware Server Profile

, press 

F10

NOTE: 

When the restore process is complete, BIOS prompts to restore the system configuration

 

data.

•

To restore the system configuration data, press 

Y

•

To use the default configuration settings, press 

N

NOTE: 

After the restore process is complete, system reboots.

Manually update the Service Tag

After replacing a system board, if Easy Restore fails, follow this process to manually enter the Service Tag, using 

System Setup

.

About this task

If you know the system service tag, use the 

System Setup

 menu to enter the service tag.

Steps

1 

Turn on the system.

2 

To enter the 

System Setup

, press 

F2

.

3 

Click 

Service Tag Settings

.

4 

Enter the service tag.

NOTE: 

You can enter the service tag only when the Service Tag field is empty. Ensure that you enter the correct service 

tag. Once the service tag is entered, it cannot be updated or changed.

5 

Click 

OK

.

148

Dell EMC PowerEdge T440 Installation and Service Manual
Installing and removing system components

Summary of Contents for EMC PowerEdge T440





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands