Dell Alienware Aurora R8 Service Manual Download

Page: 26 / 113

Removing the top-cover assembly

WARNING: Before working inside your computer, read the safety information that shipped with your computer and

follow the steps in

Before working inside your computer

. After working inside your computer, follow the instructions

After working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Prerequisites

Remove the

left-side cover

2 Remove the

right-side cover

Procedure

Remove the two screws (#6-32 X 1/4") that secure the top cover to the chassis.

2 Disconnect the lighting cable from the top cover.

3 Slide the lighting cable through the slot on the chassis.
4 Starting from the rear, release the tabs on the top cover from the slots on the chassis.

Summary of Contents for Alienware Aurora R8


















































































































Search results

Summary of Contents for Alienware Aurora R8

Reviews:

Related manuals for Alienware Aurora R8

Brands by name

Popular brands

Dell Alienware Aurora R8, Service Manual

Search results

Summary of Contents for Alienware Aurora R8

Reviews:

Related manuals for Alienware Aurora R8

Brands by name

Popular brands