Dell Alienware Area-51 R5 Service Manual Download Page 47 | Manualshive

Page: 47 / 121

background image

Replacing the graphics card

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working

inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

.

Procedure

1. Align the graphics card with the PCI-Express card connector on the system board.
2. Place the card in the connector and press down firmly. Ensure that the card is firmly seated.

3. Press and hold the securing tab on the clamp.
4. Push the clamp back towards the bracket.
5. Rotate the PCIE door to close.
6. Connect the power cables to the graphics card.

NOTE: The location of the power supply connector (VGA1, VGA2, and VGA3) varies depending on the video card
installed.

47

«
...
45
46
47
48
49
...
»

Summary of Contents for Alienware Area-51 R5


























































































































Reviews:

No comments

Related manuals for Alienware Area-51 R5

Brand: AURES Pages: 63

EBOX-335xDX3 Series

Brand: DMP Electronics Pages: 40

Brand: eMachines Pages: 46

Brand: Aaeon Pages: 116

Brand: Asus Pages: 54

Brand: Asus Pages: 70

AAEON BOXER-6710

Brand: Asus Pages: 75

Brand: Asus Pages: 70

Brand: Asus Pages: 50

Brand: Asus Pages: 64

Brand: Asus Pages: 70

Brand: Asus Pages: 62

Brand: Asus Pages: 71

Brand: Asus Pages: 76

Brand: Asus Pages: 74

Brand: Asus Pages: 60

Brand: Asus Pages: 68

Brand: Asus Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands