Dell Alienware Area-51 R4 Service Manual Download

Page: 62 / 128

Removing the top fan

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working

inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Prerequisites

1. Remove the

stability foot

2. Remove the left and right side-panels. See “

Removing the side panels

”.

Procedure

1. Lay the chassis on the right side.
2. Remove the screw (#6-32x6) that secures the top fan on the chassis.
3. Pull the release tab away from the chassis and move the top fan towards the right side.
4. Lift the top fan out of the chassis.

1. top fan

2. release tab

3. screw

4. memory-fan cable

Summary of Contents for Alienware Area-51 R4

































































































































Search results

Summary of Contents for Alienware Area-51 R4

Reviews:

Related manuals for Alienware Area-51 R4

Brands by name

Popular brands

Dell Alienware Area-51 R4, Service Manual

Search results

Summary of Contents for Alienware Area-51 R4

Reviews:

Related manuals for Alienware Area-51 R4

Brands by name

Popular brands