manualshive.com logo in svg

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 188 / 209

Share
Download
Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 188

Table 63. Cooling fan specifications (continued)

Fan type

Label color

Label name

Label image

Very high
performance fan
(Gold grade)

Gold

Very high
performance (Gold
grade)

NOTE:

 Mixing of STD, HPR, or VHP fan is not supported.

NOTE:

 The STD, HPR, or VHP fan installation depends on the system configuration. For more information about the

supported fan configuration or matrix, see 

Thermal restriction matrix

.

System battery specifications

The PowerEdge R7525 system supports CR 2032 3.0-V lithium coin cell system battery.

Expansion card riser specifications

The PowerEdge R7525 system supports up to eight PCI express (PCIe) Gen 4 expansion cards.

Table 64. Expansion card slots supported on the system board 

PCIe

slot

With

Regular

shroud

PCIe slot

length

R1a

R1b

R1c

R2a

R3a

R3b

R4a

R4b

R4c

Slot 1

Low profile

and Full
Height-

Half Length

Low

profile

and Full
Height-

Half

Length

x8

x16

Slot

2

Low profile

and Full
Height-

Half Length

Full

Height-3/

4 and Full

Length

x16(GPU

)

x8

x16

Slot

3

Low

profile-Half

Length

x16

Slot

4

Low profile

and Full
Height-

Half Length

x8

Slot

5

Low profile

and Full

Full

Height-3/

x16(GPU)

x8

188

Technical specifications

Summary of Contents for PowerEdge R7525


















































































































































































































Reviews:

No comments