manualshive.com logo in svg

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 194 / 209

Share
Download
Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 194

ASHRAE A4 environment

•

Two PSUs are required in redundant mode, however PSU failure is not supported.

•

PCIeSSD is not supported.

•

128 GB or greater capacity DIMMs are not supported.

•

GPU and FPGA are not supported.

•

CPU TDP equal or greater than 155 W are not supported (Only 120W processor supports A4).

•

Rear drives are not supported.

•

12 x 3.5 chassis is not supported.

•

BOSS and OCP are not supported.

•

OCP 3.0 card is not supported.

•

Non Dell qualified peripheral cards and/or peripheral cards greater than 25 W are not supported.

Thermal restriction matrix

Table 80. Thermal restriction matrix 

Configuration

8 x 2.5-

inch

NVMe

16 x 2.5-

inch

SAS

16 x 2.5-

inch

NVMe

16 x 2.5-

inch

SAS + 8

x 2.5-

inch

NVMe

24 x 2.5-

inch

NVMe

8 x 3.5-

inch

12 x 3.5-inch

Ambient

temperatu

re

Rear storage

No Rear

Drives

No Rear

Drives

No Rear

Drives

No Rear

Drives

No Rear

Drives

No Rear

Drives

No Rear

Drives

2 x Rear

2.5-inch

No Rear

Fan

CPU

TDP/
cTDP

120 W

STD fan

1U STD

HSK

STD fan

1U STD

HSK

STD fan

1U STD

HSK

STD fan

1U STD

HSK

HPR fan

1U STD

HSK

STD fan

1U STD

HSK

HPR fan

1U STD

HSK

HPR fan

1U STD

HSK

35°C

155 W

STD fan

1U STD

HSK

STD fan

1U STD

HSK

STD fan

1U STD

HSK

STD fan

1U STD

HSK

HPR fan

1U STD

HSK

STD fan

1U STD

HSK

HPR fan

1U STD

HSK

HPR fan

1U STD

HSK

35°C

170 W

STD fan

1U STD

HSK

STD fan

1U STD

HSK

STD fan

1U STD

HSK

STD fan

1U STD

HSK

HPR fan

1U STD

HSK

STD fan

1U STD

HSK

HPR fan

1U STD

HSK

HPR fan

1U STD

HSK

35°C

180 W

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan

2U Full

HSK

HPR fan

2U Full

HSK

35°C

200 W

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan

2U Full

HSK

HPR fan

2U Full

HSK

35°C

225 W

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan

2U Full

HSK

HPR fan

2U Full

HSK

35°C

240 W

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan

2U Full

HSK

HPR fan

2U Full

HSK

35°C

280 W

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

STD fan

2U Full

HSK

HPR fan +

2U Full

HSK

STD fan

2U Full

HSK

HPR fan +

2U Full

HSK

HPR fan +

2U Full

HSK

35°C

NOTE:

Only
12x3.5

194

Technical specifications

Summary of Contents for PowerEdge R7525


















































































































































































































Reviews:

No comments