Home
/
Dell EMC
/
PowerEdge R7525
/
Installation And Service Manual

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 180 / 209

Share

Page: 180 / 209

Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 180

Jumpers and connectors

This topic provides some basic and specific information about jumpers and switches. It also describes the connectors on the various
boardsboard in the system. Jumpers on the system board help to disable the system and reset the passwords. To install components and
cables correctly, you must know the connectors on the system board.

Topics:

•

System board connectors

•

System board jumper settings

•

Disabling a forgotten password

System board connectors

Figure 135. System board jumpers and connectors

Table 57. System board jumpers and connectors

Item

Connector

Description

1.

SL5_CPU2_PA4_SA1

PCIe/NVMe/SATA connector 5

2.

IO_RISER4 (CPU2)

Riser 4

7

180

Jumpers and connectors

«
...
178
179
180
181
182
...
»

Summary of Contents for PowerEdge R7525


















































































































































































































Reviews:

No comments