Dell EMC PowerEdge R7525 Installation And Service Manual Download Page 147

Page: 147 / 209

Figure 106. Installing the Serial COM port

Next steps

1. Reconnect the serial COM port cable to the connector on the rear I/O board.
2.

Install the expansion card riser

3. Follow the procedure listed in

After working inside your system

on page 47.

Optional IDSDM module

Removing the IDSDM module

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 46.

2. Follow the procedure listed in the

Before working inside your system

on page 47.

3. If you are replacing the IDSDM module,

remove the MicroSD cards

NOTE:

Temporarily label each SD card with its corresponding slot number before removal. Reinstall the SD cards

into the corresponding slots.

Steps

Holding the blue pull tab, lift the IDSDM module out of the system.

Installing and removing system components

147

Summary of Contents for PowerEdge R7525


















































































































































































































Search results

Summary of Contents for PowerEdge R7525

Reviews:

Dell EMC PowerEdge R7525, Installation And Service Manual, Page: 147 / 209

Search results

Summary of Contents for PowerEdge R7525

Reviews: