background image

Steps

1. Align and place the base cover on the computer, press the edges and sides of the base cover until it snaps into place.

2. Tighten the eight (M2.5x2.5) screws to secure the base cover to the computer.

Next steps

1. Replace the 

SD Card

.

2. Follow the procedure in 

after working inside your computer

.

Battery

Lithium-ion battery precautions

CAUTION:

• Exercise caution when handling Lithium-ion batteries.
• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting

the AC adapter from the system to allow the battery to drain.

• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
• Do not expose the battery to high temperatures, or disassemble battery packs and cells.
• Do not apply pressure to the surface of the battery.
• Do not bend the battery.
• Do not use tools of any kind to pry on or against the battery.
• Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental puncture or

damage to the battery and other system components.

• If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending,

or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for
assistance. See 

www.dell.com/contactdell

.

• Always purchase genuine batteries from 

www.dell.com

 or authorized Dell partners and resellers.

Removing the battery

Prerequisites

1. Follow the procedure in 

before working inside your computer

.

2. Remove the 

microSD card

.

3. Remove the 

base cover

.

24

Disassembly and reassembly

Summary of Contents for Latitude 3510














































































Reviews: