Dell EMC Latitude 3510 Service Manual Download | Manualshive

Page: 20 / 77

background image

Installing the SIM card

About this task

Steps

1. Open the latch that covers the SIM card slot to release it from the system.
2. Insert the SIM card removal tool in the slot and push it to eject the SIM card tray [2].
3. Pull the SIM card holder out of the slot.
4. Place the SIM card into the SIM card holder.
5. Slide the SIM card tray into the slot until it clicks into place.

Next steps

Follow the procedures in

After working inside your computer

Base cover

Removing the base cover

Prerequisites

1. Follow the procedure in

before working inside your computer

20

Disassembly and reassembly

«
...
18
19
20
21
22
...
»

Summary of Contents for Latitude 3510














































































Reviews:

No comments

Related manuals for Latitude 3510

Brand: Gateway Pages: 10

Brand: Gateway Pages: 87

Brand: Panasonic Pages: 13

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 112

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 192

Toughbook CF-T7BWATAAM

Brand: Panasonic Pages: 44

Toughbook CF-F8EWDZZAM

Brand: Panasonic Pages: 20

Toughbook CF-19CHBAXBM

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 40

The Toughbook 52

Brand: Panasonic Pages: 2

Brand: IBM Pages: 94

Brand: IBM Pages: 102

Brand: IBM Pages: 96

Brand: IBM Pages: 96

Brand: IBM Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands