Dell EMC ECS D Series Hardware Manual Download Page 23 | Manualshive

Page: 23 / 114

background image

Table 14 C-Series (Gen1) upgrades

Model number

Disk upgrade (to the next
higher model)

Hardware upgrade (to
the next higher model)

2 Phoenix-12 Compute
Servers (minimum
configuration)

Not applicable

Not applicable

3 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes)

4 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes)

5 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes)

6 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes)

7 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes) and one private and
two public switches

8 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes)

9 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes)

10 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes)

11 Phoenix-12 Compute
Servers

12 integrated disks

One server chassis (four
nodes)

12 Phoenix-12 Compute
Servers (maximum
configuration)

12 integrated disks

One server chassis (four
nodes)

Certified hardware in support of ECS 3.2

The following table lists the latest hardware pre-qualified for a Certified installation.

Note

All Arista switch models listed also ship standard with the ECS Appliance.

Table 15 ECS Certified hardware

Server models

Switch models

l

Dell DSS7000

l

Dell R730xd

l

HP Proliant SL4540 Gen8

One 1 GbE private switch is required to handle
management traffic:

l

Arista 7010T- 48

l

Arista 7048T

Hardware Components and Configurations

Certified hardware in support of ECS 3.2

23

«
...
21
22
23
24
25
...
»

Summary of Contents for ECS D Series



















































































































Reviews:

No comments

Related manuals for ECS D Series

Brand: Quantum Pages: 32

DiamondMax Plus9 120GB AT

Brand: Maxtor Pages: 79

HyperDrive COLORSPACE

Brand: SANHO Pages: 31

Brand: Buffalo Pages: 2

Forensic ComboDock FCDv6

Brand: WiebeTech Pages: 20

Brand: National Instruments Pages: 20

OmniStor 4900F Series

Brand: Rackable Systems Pages: 196

Brand: Compaq Pages: 139

Hybrid Home 4,8

Brand: Hybrid Pages: 42

Brand: DEC Pages: 94

Brand: Mercia Garden Products Pages: 9

Brand: Transcend Pages: 25

Brand: Husky Pages: 4

Brand: Archos Pages: 12

Brand: Yardmaster Pages: 28

Storwize V5000E

Brand: IBM Pages: 120

Brand: NEC Pages: 16

Brand: DataON Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands