Dell EMC E68S Installation And Service Manual Download

Page: 44 / 187

Figure 34. Removing the cooling fan cage assembly

Next steps

Install the cooling fan cage assembly

Installing the cooling fan cage assembly

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 26.

CAUTION:

Ensure that the cables inside the system are correctly installed and retained by the cable

retention bracket before installing the cooling fan cage assembly. Incorrectly installed cables may get
damaged.

2. Follow the procedure listed in

Before working inside your system

on page 27.

3. If installed,

remove the air shroud

Steps

1. Align the guide rails on the cooling fan cage assembly with the standoffs on the system.
2. Lower the cooling fan cage assembly into the system until the cooling fan cage connectors engage with the connectors on

the system board.

3. Press the release levers to lock the cooling fan cage assembly into the system.

Installing and removing system components

Summary of Contents for E68S




























































































































































































Search results

Summary of Contents for E68S

Reviews:

Related manuals for E68S

Brands by name

Popular brands

Dell EMC E68S, Installation And Service Manual

Search results

Summary of Contents for E68S

Reviews:

Related manuals for E68S

Brands by name

Popular brands