Dell EMC E68S Installation And Service Manual Download | Manualshive

Page: 180 / 187

background image

Table 46. NIC indicator codes (continued)

NIC indicator codes

Condition

Link indicator is green, and activity indicator is blinking
green.

Indicates that the NIC is connected to a valid network at its maximum
port speed, and data is being sent or received.

Link indicator is amber, and activity indicator is blinking
green.

Indicates that the NIC is connected to a valid network at less than its
maximum port speed, and data is being sent or received.

Link indicator is green, and activity indicator is off.

Indicates that the NIC is connected to a valid network at its maximum
port speed, and data is not being sent or received.

Link indicator is amber, and activity indicator is off.

Indicates that the NIC is connected to a valid network at less than its
maximum port speed, and data is mot being sent or received.

Link indicator is blinking green, and activity is off.

Indicates that the NIC identify is enabled through the NIC
configuration utility.

Power supply unit indicator codes

AC power supply units (PSUs) have an illuminated translucent handle that serves as an indicator. The indicator shows if power is
present or if a power fault has occurred.

Figure 155. AC PSU status indicator

1. AC PSU handle
2. Socket
3. Release latch

Table 47. AC PSU status indicator codes

Power indicator codes

Condition

Green

Indicates that a valid power source is connected to the PSU
and the PSU is operational.

Blinking amber

Indicates an issue with the PSU.

Not powered on

Indicates that the power is not connected to the PSU.

Blinking green

Indicates that the firmware of the PSU is being updated.

CAUTION:

Do not disconnect the power cord or

unplug the PSU when updating firmware. If firmware
update is interrupted, the PSUs do not function.

Blinking green and powers off

When hot-plugging a PSU, it blinks green five times at a rate
of 4 Hz and powers off. This indicates a PSU mismatch due to
efficiency, feature set, health status, or supported voltage.

CAUTION:

If two PSUs are installed, both the PSUs

must have the same type of label; for example,
Extended Power Performance (EPP) label. Mixing
PSUs from previous generations of PowerEdge
servers is not supported, even if the PSUs have the

180

System diagnostics and indicator codes

«
...
178
179
180
181
182
...
»

Summary of Contents for E68S




























































































































































































Reviews:

No comments

Related manuals for E68S

Brand: IBM Pages: 214

Brand: NEC Pages: 151

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Modbus Server-FC330A

Brand: IntesisBox Pages: 5

Brand: Flexport Pages: 39

Brand: Icy Box Pages: 17

Alcatel-Lucent OXO Connect Compact

Brand: Nokia Pages: 216

Turbo NAS TS-219P

Brand: QNAP Pages: 49

Brand: BITMAIN Pages: 20

Brand: Supermicro Pages: 96

Brand: Supermicro Pages: 130

Brand: Supermicro Pages: 124

Brand: Multitech Pages: 35

AcquiLite A7810

Brand: Obvius Pages: 29

Brand: Chip PC Pages: 4

JackPC EFI-6700

Brand: Chip PC Pages: 4

DIGIARRAY DA-4000E

Brand: Digiever Pages: 9

Brand: Measy Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands