DEL PowerVault 124T DLT VS160 User Manual Download

Page: 71 / 79

Technical Specifications: Dell PowerVault 124T DLT VS160 Autoloader User's Guide

file:///T|/htdocs/stor-sys/124T/en/124tvs16/specs.html[12/5/2012 10:26:14 AM]

Back to Contents Page

Technical Specifications: Dell™ PowerVault™ 124T DLT VS160

Autoloader User's Guide

Physical Specifications

Autoloader Performance Specifications

Autoloader Environmental Specifications

Autoloader Power Specifications

Autoloader Vibration Specifications

Autoloader Shock Specifications

Tape Drive Specifications

Physical Specifications

Characteristic

Product Alone

Height

8.9 cm (3.5 in)

Width

45 cm (17.7 in)

Length

75.46 cm (29.71 in)

Package Weight (without media) 22.7 kg (50 lb)

Footprint

0.32 square meters (3.4 square feet)

Autoloader Performance Specifications

Characteristic Specification

Maximum data

transfer rate

Native: 28.8 GB/hr

Compressed: 57.6 GB/hr (assuming 2:1 compression ratio)

Drive type

1 DLT VS160 drive

Number of slots

16 (8 per magazine)

MCBF

400,000 cycles

Summary of Contents for PowerVault 124T DLT VS160
















































































Search results

Summary of Contents for PowerVault 124T DLT VS160

Reviews:

Related manuals for PowerVault 124T DLT VS160

Brands by name

Popular brands

DEL PowerVault 124T DLT VS160, User Manual

Search results

Summary of Contents for PowerVault 124T DLT VS160

Reviews:

Related manuals for PowerVault 124T DLT VS160

Brands by name

Popular brands