1. CAUTION:
( Non-Condensing )
2.3 Storage temperature
-10
60
,
90%RH ( Non-Condensing )
2.4 Power supply
Power supplied by power board
DC 12V
(If communication wire is over 100 meters, an extra power DC12V is required)
2.5 Temperature display range
0
50
in 0.5
steps.
2.6 Communication wire
2 wires(pdes) + isolated wire (connect GND), UL2464 / 24AWG
with isolated wires.
2.7 Communication protocol
Modbus-RTU (RS485)
2.8 Max communication distance1200M
2.9 Max control qty. Can control 63 sets of Pns
DEI-
2.10 Alarm contact
buzzer
2.11 District control Divide FCUs into 4 districts control (group control/ schedule).
DEI-201N AHU/ VAV
can't be divided into district control.
3. FUNCTION DESCRIPTION :
3.1 Buttons description
3.1.1 POWER
To switch on / off the power, set district control/ schedule of power status.
3.1.2
Set temp./ max limit for heating/ min limit for cooling/ room temp.
calibration (0.5
) or into max limit for heating setting.
3.1.3
Set temp./ max limit for heating/ min limit for cooling/ room temp.
1.1 Please install according to the wiring diagram to avoid incorrect wiring, any improper
wiring or installation is beyond our warranty.
1.2 Please do not install it in humid environment to ensure good signal communication.
1.3 Please use the communication wire UL2464/24AWG or 26AWG 3C communication
isolated wire.
2. SPECIFICATION:
2.1 Appearance
2.2 Operation temperature
0
50
,
90%RH
758PN/758FPN/100A/100D/201NAHU/
201NVAV
calibration (-0.5
) or into min limit for cooling setting.
3.1.4 IP
& IP
To select the fan IP, or into group control status.
3.1.5 Mode
To setup the mode of fan coil unit (in single or group), or daily schedule setting.
3.1.6 Fan
To setup the fan speed (in single or group), or into room temp. calibration setting.
3.1.7 Light
To switch on/ off the LCD backlight or into parameter setting.
3.1.8 Lock
To lock or unlock the panel.
3.2 Function
3.2.1 IP address of PN
It displays the monitored and controlled PNs' address from 01~63;
displays AL or A1~ A4 for the district control; displays AC for controlling all of PNs.
When icon is not illuminated, it means there is abnormal communication between SCN
and PN.
3.2.2 Power
Control the selected PN or all PNs or district PNs (schedule), power on / off
status.
3.2.3 Temperature setting
3.2.3.1 When setting temperature, the panel shows the setpoint (it back to room
temperature if the up / down buttons have not been pressed within 5 seconds).
In normal situation, the display shows the room temperature of the monitored
PN (icon of room temperature shows on)
3.2.3.2 Temperature setting range
heating: 0
~max limit of heating, cooling: min
limit of cooling ~35
(0.5
in step)
3.2.3.3 Whenever temperature setting is adjusted (by LCN or PC), the display shows
the new setpoint for 5 seconds.
3.2.4 Mode control
3.2.4.1 To setup the mode status of the single PN or group PNs (Auto, cooling, fan, he
ating and humidity).
3.2.4.2 When changing to auto air conditioning, cooling or heating mode, fan speed
will be changed to Auto.
3.2.4.3 When changing to fan or dehumidifying mode, fan speed will be changed to
Low.
3.2.5 Fan speed control
To setup 4 fan speeds for the single or district (all districts) PNs
( Auto, High, Medium and Low). No auto speed under the fan and
dehumidifying mode.
3.2.6 Lock function
3.2.6.1 Press Lock button, the display will show the lock icon and the sub controller
will be locked. To unlock the panel, press Lock button again.
3.2.6.2 Press Lock button within 3 seconds, the display shows LC. Under this mode,
the main controller is locked; besides Power, IP selection, Light and Lock,
other buttons are not available to operate. Press lock again within 3 seconds,
to unlock the panel. Under group control, only setting power status.
3.2.6.3 Once setup lock from PC, the display shows LP. Under this mode, the main
controller is locked; besides Power, IP selection, Light and Lock, other buttons
are not available to operate, only can be unlocked by PC operation. In Group
control, only the power button is available.
3.2.7 Max limit heating setting
(
DEI-758FPN / 201NAHU / 201NVAV
)
When
DEI-758FPN/201NAHU / 201NVAV
in OFF status, press for 3 seconds into
max limit heating setting (show HS) and adjust by .
Setting range
0
~ 35
. Under setting status, press IP
to into AL-HS setting.
After completing setting, press Light to save or press Fan to cancel.
-758SCNE Operational Manual
-758SCNE Operational Manual
Version 02
5INSLL20503
Button description
Fan IP +1
Fan IP -1
Backlight/
confirm
To increase
temp.
To decrease
temp.
Lock /Week
Mode / Select
Fan / Cancel
3
4
2
1
5
Light
Mode
Fan
Lock
POWER
IP
IP
Power
Room Temp.
/Set Temp
IP address for
SCN / Time
Su
Tu
Th Fr Sa
3
4
2
1
5
ON
OFF
IP address
of PN
Room Temp.
Symbol
Week
Weekday
operation
Mode
Unit
Lock
Fan speed
Link status
LCD display
Separated line
Swing