background image

Maintenance

The maintenance intervals for the dehumidifier 

depend on the surrounding environment and 

installation site. Recommended maintenance 

intervals could therefore differ from one instal-

lation to another. Incorrect maintenance and 

service may result in reduced dehumidification 

capacity.

Filters

The dehumidifier is equipped with two separate 

filterbanks, one for the process air and the other 

for the reactivation air. The filters are positioned 

at the respective inlets and will clean the air 

prior to entering the dehumidifier.
Intervals for cleaning or replacement of the 

filters will be determined by the amount of dust 

and particles in the air at the installation site.
We recommend that the filters are checked at 

least once a month.
The unit can be equipped with differential pres-

sure measurement for checking the pressure 

drop over the filters.
Never operate the dehumidifier without the fil-

ters, as the rotor can be damaged by dust.

Rotor

The rotor is maintenance free. However should 

it be necessary to clean the rotor careful use of 

compressed air should be the first choice. With 

severe contamination the rotor can be washed 

with water.

Cleaning with water is no routine matter, please 

contact DehuTech AB or local distributor prior 

to this procedure.
Check the rotor bearing and the rotor surface 

once a year.

Electrical motors

The electrical motors are equipped with ball 

bearings. The bearings are designed to last the 

life of the motor and therefore no maintenance is 

required.
Check the motors once a year for any abnormal 

sound.

Heater

The reactivation electric heater does not need 

maintenance, but should be checked twice a year 

for any mechanical damage to the heating rods.

Rotor drive belt

Check the belt tensioning at regular intervals. 

The tensioning is maintained constantly by the 

belt tension device, and should not need to be 

adjusted during normal operation.

Sealings

Check the sealings at regular intervals for leak-

age, damage and dust.

NOTE ! With all maintenance and service of the 

dehumidifier:

• 

Switch off the dehumidifier  approximately 

15 minutes prior to opening any service 

panel, allowing the heater to cool down.

• 

Disconnect the dehumidifier from main 

electrical supply by turning the external 

switch to the off position.

9

Subject to change without notice

DehuTech 2400

Summary of Contents for 2400



















Reviews: