Deeplas ENVIROTILE Installation Manual Download Page 32 | Manualshive

Page: 32 / 44

Deeplas ENVIROTILE Installation Manual Download Page 32

3 2

| E N V I R O T I L E I N S T A L L A T I O N G U I D E

18. INSTALLING ENVIROTILES

18

CHECK THAT THE COURSE LINE IS LEVEL ON ALL ROOF FACES

Laying Envirotiles on a hipped roof face follows the same basic procedure as outlined in pages 20 to 25 of this guide.

But there are some differences that need to be considered due to the warm roof structure.

In a warm roof construction the Envirotiles are fixed directly onto the plywood

roof face panels. There are no battens so it is very important that the installer

checks that the first course line is level. The easiest way to do this is to clip

a single tile into the starter rail at each end of each roof face and run a line

as shown. Adjust the line so it is level - the starter rail allows for some tile

adjustment.
We recommend marking the line on the roof face as a reference.

Starting at the right hand side of the roof face, clip a

DOUBLE TILE into the starter rail, locate and position

the tile and trim to match the hip as shown. Ensure

that you leave 20-25mm of clearance at the edge to

allow for ventilation and expansion.
You may wish to used a tile sized paper template to

help with this.

The nibs on the Envirotile raise the back of the tile off

the roof face so maintaining a ventilation path.

It is very important that the tiles are clipped into the

starter rail - this is an essential part of installation to

ensure that the first course is properly secured.

Detachable

Nib F

Cut tile

Detachable

Nib F

Level

Level

«
...
30
31
32
33
34
...
»

Summary of Contents for ENVIROTILE













































Reviews:

No comments