manualshive.com logo in svg

DCS DishDrawer DD24DUT7, Installation Instructions Manual, Page: 21 / 32

Share
Download
DCS DishDrawer DD24DUT7 Installation Instructions Manual Download Page 21

4

PARTS SUPPLIED

2

Phillips 

5⁄8” (16 mm) 

screws (7)

1½  ” (38 mm)

bottom fixing 

screws & metal 

washers (2)

Drain hose 

support (1)

Drain hose 

joiner (1)

Side mounting

bracket kit

(A and B)

 (2)

OPTIONAL

If the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hoses by 11’ 10” (3.6m). 

The kit is available from the nearest DCS by Fisher & Paykel Authorized Service Center, or Toll free 1.888.936.7872 or www.dcsappliances.com

Edge Protector (1)

(If the services hole is through 

a metal partition the hole 

must be protected with the 

Edge protector supplied to 

prevent damage to the power 

cord or hoses.)

Wire clip (1)
(

for securing 

Drain hose joiner)

Moisture protection 

tape (1)

(to prevent moisture 

damage) 

Clamp (1)
(

for securing 

Drain hose joiner)

Rubber 

washer for 

inlet hose (1)

(comes already 

fitted)

Summary of Contents for DishDrawer DD24DUT7

































Reviews:

No comments