VIO S218F
420120416Q REV1.0
QUICK START USER MANUAL SECTION 1
2
PPU
USSH
H
VIO S218
VIO S218F
(flyable)
PPU
USSH
H
PPU
USSH
H
Data Out
Data In
R
RD
DN
Neett
Link
Active
Remote
Preset Active
Expansion Card
DESIGNED & DEVELOPED
IN ITALY
System test
Push and Hold to test
Active
Signal
Mute/Prot
Balanced
Audio
Input
Link
USB Data Service
Status
Mute
Delay [ms]
Cardioid preset
Polarity
HPF
Xover output
LPF
Subwoofer Attenuation
Xover [Hz]
Service / User
When green light is on, polarity and delay are bypassed
0
.0
-6
dB
60
1
.1
-3
dB
70
2
.2
-2
dB
75
3
.3
-1
dB
80
4
.4
0
dB
85
90
5
.5
6
.6
-24
dB
100
7
.7
-18
dB
110
8
.8
-12
dB
Fullrange
9
.9
-9
dB
180°
0°
Ready
Limiter
1
2
9
3
5
7
4
6
8
11
10
The DigiPro G4 amplifier of VIO S218F is controlled by a
powerful DSP. All the connections and controls are in the
rear amplifier control panel.
1-
Balanced audio input and output link
2-
Polarity switch
3-
Delay rotary control
4-
Cardioid preset switch
5-
Status LEDs (Limiter, Signal, Mute/Protection,
Ready)
6-
Subwoofer attenuation rotary control
7-
System Test button
8-
Mini B-type USB port for firmware update
9-
RDNet Data In / Data Out and Control LEDs
10-
HPF Xover (balanced) output
11-
Xover rotary control
12-
Full-range Mains input
13-
Mains Link output
14-
Mains Fuse
I/O and Control panel
Setup, turn on and I/O settings
Connect first the audio input (1); if you need to link the VIO S218F to another one, please use a cable with XLR connectors (not
supplied). Connect the Link output of the first, to the balanced Input of the second one, and so on.
Plug properly the mains POWERCON TRUE1 cable (supplied) in the related input (12) to turn on the system.
In case of remote control, connect the Data Input of the subwoofer to the hardware remote controller (RDNet Control 2 or RDNet
Control 8) with cables equipped with etherCON connectors; to link another subwoofer connect the Data Output of the first, to the
Data Input of the second one, and so on. Please use a cable with etherCON connectors. When the subwoofer is active and the RD-
Net network is active and it has recognized the connected device, the LED Link is on. The “Active” LED will start flashing to indicate
the presence of data traffic; the “Remote Preset Active” signals that all the local controls set on the amplifier panel (DSP preset) are
by-passed and controlled remotely by RDNet remote control.
See also RDNet Control 2 or RDNet Control 8 user manuals for further information.
12
14
13
110000--224400V
V~~ 5500--6600H
Hzz
M
MA
AIIN
NSS LLIIN
NK
K
FFU
ULLLL--R
RA
AN
NG
GEE
M
MA
AIIN
NSS IIN
NPPU
UTT
OFF
ON
OFF
ON
222200--224400V
V~~ ((99,,44A
Am
maaxx)) 22115500W
Wm
maaxx
110000--112200V
V~~ ((77,,77A
Am
maaxx)) 888800W
Wm
maaxx
222200--224400V
V~~ 5500--6600H
Hzz 66,,66A
A
110000--112200V
V~~ 5500--6600H
Hzz 1122,,33A
A
MAINS FUSES
(REPLACE FUSES WITH SAME RATINGS)
(REMPLACER FUSIBLES AVEC LE MÊME TYPE)
110000--112200V
V~~ ((TT1100A
A LL 225500V
V~~))
222200--224400V
V~~ ((TT55A
A LL 225500V
V~~))
POWER SUPPLY SPECIFICATIONS (POWER ABSORPTION)
Draw at 1/8 of full power in average use conditions (*): 3,2 A (220-240V~) - 5 A (100-120V~)
Draw at 1/3 of full power in maximum use conditions (**): 6,6 A (220-240V~) - 12,3 A (100-120V~)
Power absorption with speaker turned on without signal (idle): 53 W
*INSTALLER NOTES: The values refer to 1/8 of full power, in average operating conditions (music program with infrequent or no clipping). It is
recommended to consider them the minimum sizing values, for any type of configuration.
**INSTALLER NOTES: The values refer to 1/3 of full power, in heavy operating conditions (music program with frequent clipping or activation of
the limiter. We recommend sizing according to these values in case of professional installations and tours
