background image

Panel controls and features

T

1

A.POWER STATUS LED

B.PHASE SHIFT

Use this switch to help compensate for time 

alignment problems in the system. Such 

problems usually result from having the 

subwoofer at a  different distance from the 

listener than the other speakers in the system.

C.AUTO POWER ON

D.LOW PASS FILTER

his control alows you fine tune the frequency 

range you want the subwoofer amplifier will 

receive. 

F.INPUT GAIN CONTROL

After you have installed your system, turn this 

control to minimum.

Turn the head unit on (and the subwoofer will 

turn on via the remote connection). Turn the 

head unit volume to about 2/3 full level.
Slowly turn up the subwoofer input gain control 

until you hear a small amount of distortion. Then 

reduce the level until the distortion is completely 

gone. Level the control at this setting.

G.REMOTE LEVEL CONTROL 

Attach the included remote level control to 

control the volume level of the subwooer

independently.

H.HIGH LEVEL (speaker level) INPUTS

If your head unit does not have RCA outputs

you can use the speaker outputs for the audio

source for the subwoofer. Use the supplied 

cable and wire harness and connect the 

outputs properly as shown in the connection

diagram in this manual.

I.LOW LEVEL RCA INPUTS

Low level inputs are the recommended way

to introduce the audio signal into your subwoofer.

J.FUSE

K.POWER INPUT TERMINAL

This bi-color LED glows green when power is

on and no problems are present. If one of the

protection circuits comes on, it will change to

red.

Do not use a fuse with a different value

other than the origional value.

T

E.BASS BOOST

he BASS BOOST feature will increase the 

sound level in the bass frequencies.

The AUTO POWER ON(ON/OFF) is for high

level(speaker-level)  connections.  When  the 

switch is in the “ON” position, the subwoofer 

will AUTO POWER ON when there is signal 

input. If the amplifier detects no signal input, 

the amplifier will auto power off. If you prefer 

to  use  the  remote  turn  on/off  connection, 

leave switch in the “OFF” position.

If RCA outputs are present on your head unit

Summary of Contents for EUPHORIA EPS8









Reviews: