background image

20

Maintenance and Troubleshooting

This section outlines problems you may have and solutions you may be able to use.

Many of the parts in this product are not user-serviceable and should be repaired by 

trained professionals. This is especially true of the electrical systems and the mechanical 

components. Alteration of these components voids the warranty.

Tire Pressure

Maintain the air pressure in your tires at the appropriate level. If the air pressure is too low, 

your e-bike’s performance will suffer and it will become damaged more easily.

Cold weather and lower temperatures will cause the air pressure in your tires to drop, and 

warmer weather will cause it to increase, even if there are no leaks in the tire tube. To re-

place the air in your tires, follow this procedure:

 

1. 

Identify the required pressure by examining the text along the side of the tire  

 

     rim. This text should indicate the recommended pressure for your tire.

 

2.

 Locate the air valve on the inner surface of the tire rim.

 

3.

 Remove the valve cap and place in a secure location.

 

4.

 Place the nozzle end of an air pump (hand-power or mechanical) over the valve.

 5.

 Pump up the air in the tire, being careful not to let the pressure go above the  

 

     level prescribed on the side of the tire wall.

 

6.

 Remove the pump nozzle from the air valve without allowing much air to escape 

 

     from the tire.

 7.

 Replace the valve cap on the air valve.

Maintaining the proper air pressure will allow you to travel much further on a single charge, 

because the motor will not have to work as hard to move the e-bike.

Replacing Flat Tires

Replacing flat tire tubes is a more complicated and labour-intensive process with e-bikes 

than it is with regular bicycles. It requires proper tools, more skill and more patience.The 

front wheel is easier to service when changing a flat tire than the rear wheel, as the rear 

wheel is connected to the hub motor and other mechanical parts.

Unless you are very familiar with the mechanical components of the rear motor, attempt-

ing to change a flat rear tire may cause serious problems. Please contact your Daymak 

dealer for specific instructions on how to remove your wheel and tires safely, and how to 

replace the tubes.

It may be easier – and safer - to have the tubes replaced by your Daymak dealer. 

Summary of Contents for Munich




























Reviews: