background image

14

TROUBLESHOOTING

Since malfunction may be caused by one or more faults, find out the real cause and then take corresponding solutions for 

troubleshooting. In you have any question, please consult professional technicians.

TROUBLE 

SHOOTING

Since one or more failure causes may cause the malfunction, you should �nd 
out the real cause and then take the corresponding solution to deal with the 
problem. If in doubt, please consult a professional technician.

Type

Fault phenomenon

Analysis and solution

battery

Instrument

The battery cannot be charged

1. The instrument cannot be

 turned on /The button on the

 LED screen is pressed without

 any response

3. The + and - buttons cannot 

be pressed simultaneously for

 LED setting.

4. The display keeps showing 

garbled or black screen after 

riding for a while.

5. The speed described in the 

Manual cannot be reached

6. The instrument does not 

display the speed.

2. The instrument cannot save 

the settings.

1. Charger failure: If the green indicator is on when the charger is 

connected to the battery for charging, use a multimeter to measure

 whether the voltage at the output port of the battery is 42V (when 

the green indicator is on after the charger is connected to the power 

supply and then connected to the battery for charging, pull out the 

connector between the charger and the battery for measurement).

 If the voltage is lower than 42V, the charger is damaged and needs

 to be replaced.

2. Battery failure:

a. Use a multimeter to measure the voltage at the battery discharg-

ing port, and judge whether the battery pack is damaged or under-

voltage protected based on the voltage.

b. If the voltage of the battery pack measured by the multimeter is 

0-5V, it indicates that the battery pack cannot be charged due to 

overdischarge. In this case, the low-voltage charger (0-3V) is requ-

ired to charge for about 3 hours to activate the battery pack that can 

operate properly after being fully charged.

d. If the battery cannot be charged due to damage of its protection 

board, replace the battery pack.

1. Check whether the outgoing line of instrument button falls off or

 is damaged.

2. Check whether the instrument outgoing line and the connection

 with the controller terminal are normal.

3. If the connecting wire is connected properly but the instrument

 fails to work, replace the instrument.

1. Adjust the speed according to the instrument manual.

2. If the speed described in the Manual still cannot be reached after 

adjustment, replace the controller and instrument.

1. Check whether the motor wire and the controller speed 

measuring wire are connected well.

2. Check whether the instrument settings are normal.

3. Check whether the rear wheel speed sensor is correctly installed.

Replace the instrument.

Replace the instrument.

Replace the instrument.

15

Summary of Contents for STALLION
























Reviews: