manualshive.com logo in svg

Davnor SA 60, Installation, Operation & Maintenance Manual

Share
Download
Davnor SA 60 Installation, Operation & Maintenance Manual Download Page 7

 

 

5 

Note

: The solenoid can either be attached directly to the filter inlet or mounted to the 

filter stand or another convenient location. 

•

  Connect the filter outlet at the filter outlet valve to the filtered water storage tank 

inlet. 

Step 6.  

Using the 1” braided hose for connection between the barbed fittings; 

•

  Connect the filtered water storage tank outlet to the pump inlet. 

•

  Connect the pump outlet to the pressure tank.  

Step 7.  

Connect the overflows to the floor drain or sump.  Use a separate drain line for 

the filtered water storage overflow. This will prevent a cross connection between the 
filter and the filtered water storage tank.  Leave an air space between the overflow drain 
line and the drain to prevent the drain from backing up into your filter. 

Step 8.  

Install the filter CIP reverse flow 

assembly downstream of the pump (figure 
3-3).

 

Step 9.  

Connect the hose from the CIP 

reverse flow valve downstream of the 
pump to the lower valve on the filter 
standpipe. 

Step 10.  

Connect the filtered water outlet 

downstream of the CIP reverse flow to the 
distribution system. 

CIP reverse 

flow assembly

 

Figure 3-3 

Figure 3-4 

Typical System Layouts

 

 

Top View

Filter

BioSand

Pump 

& 

Pressure 

Tank

Filter

BioSand

Storage Tank

Filtered Water

Storage Tank

Filtered Water

 

Pump 

& 

Pressure 

Tank

Front View

BioSand

Filter

BioSand

Filter

Storage Tank

Filtered Water

Top View

Filtered Water

Storage Tank

 

Summary of Contents for SA 60
















Reviews:

No comments

Brands by name

Popular brands

Load more brands