manualshive.com logo in svg

DAVIS Wireless Temperature/Humidity Station, Installation Manual, Page: 8 / 12

Share
Download
DAVIS Wireless Temperature/Humidity Station Installation Manual Download Page 8

8

Tighten all four sets of washers and hex nuts until the mounting bracket is firmly 
mounted on the pole.

3. Next, install the SIM Shelter. While holding the shelter against the pole, place a 

U-bolt around the pole and through the two holes on at the top of the shelter. 

4. Place a flat washer, a lock washer and a hex nut on each of the bolt ends. 

5. Using an adjustable wrench or 7/16" wrench, tighten the nuts.

6. Place the second U-bolt around the pole and through the two holes at the bottom 

of the shelter. 

7. Put a flat washer, a lock washer, and a hex nut on each bolt end, and tighten the 

hex nuts. 

8. Use 8”Cable Ties to secure sensor cable to pole to prevent fraying in wind. 

Note: 

Review the illustration below to see how the Temp/Hum Station is mounted on a pole. 

Mounting on a Pole

Mounting on a Vertical Surface

1. Using four 1/4" x 1-1/2" lag screws, attach the mounting bracket to the surface in 

the desired location.

Drill holes using a 3/16" (5 mm) drill bit. Use a carpenter’s level when marking 
the holes, to ensure that the bracket will be level. 

Flat

Washer

Lock

Washer

Hex

Nut

1/4" Flat Washer

2-1/8" U-Bolts

1/4" Hex Nut

Sensor Cable

2-1/8" U-Bolts

Summary of Contents for Wireless Temperature/Humidity Station













Reviews:

No comments