background image

Introduction: Included Components and Hardware

1

Introduction

The Integrated Sensor Suite (ISS) collects outside weather data and sends the data to a 
Vantage Pro console or Weather Envoy. Wireless and cabled versions of the ISS are 
available, as well as standard and plus versions. The Wireless ISS is solar powered and 
sends data to the console via a low-power radio. The Cabled ISS sends data and 
receives power via the console cable. 

Standard versions of the ISS include a rain collector, temperature sensor, humidity 
sensor and anemometer. The ISS Plus adds a solar radiation sensor and an ultra-violet 
(UV) sensor. Temperature and humidity sensors are mounted in a passive radiation 
shield to minimize the impact of solar radiation on sensor readings. The anemometer 
measures wind speed and direction and can be installed adjacent to ISS or apart from it, 

see “Siting the ISS and Anemometer” on page 9

 for siting guidelines. 

The solar and UV sensors are mounted next to the rain collector cone. Solar and UV 
sensors are available separately to upgrade a standard ISS. See “Appendix B: Optional 
Accessories” on page 20.

The Sensor Interface Module (SIM) contains the “brains” of the ISS and is located on the 
bottom of the radiation shield. The SIM collects outside weather data from the ISS 
sensors and then transmits the data to your Vantage Pro console or Weather Envoy. 

Included Components and Hardware

The ISS comes with all the components and hardware shown in the following illustra-
tions. If you purchased your ISS as part of a Weather Station, additional components may 
be included in the package that are not shown here.

Components

Note:

Do not touch the small white diffusers on top of the UV and solar radiation sensors. Oil from skin 
reduces their sensitivity. Clean using ethyl alcohol on a soft cloth. NO RUBBING ALCOHOL.

Debris Screen

(Place inside cone  

after installation)

Rain 
Collector

Solar Panel 
(Wireless 
ISS Only)

Radiation
Shield

Anemometer 

Base

Anemometer 

Vane

Drip 

Ring

Wind Cups

Anemometer Cable 

40' (12.2 m)

Anemometer

Arm

Control

Head

Console Cable 100' (30 m) 

(Cabled ISS Only)

SIM Housing

ISS Base

UV and  
Solar Sensors
(ISS Plus Only)

Sensor 
Mounting Shelf 
(ISS Plus Only)

Summary of Contents for 6320

























Reviews: