background image

11

Contacting Davis Instruments

(510) 732-7814

 for Technical Support, Monday – Friday, 7:00 a.m. – 5:30 p.m. Pacific 

Time. 

(800) 678-3669

 Toll-Free Order Line, Monday – Friday, 7:00 a.m. – 5:30 p.m. Pacific 

Time. Our customer service representatives can answer most questions and assist you 
with your purchases. 

(510) 732-9229

 For callers outside the USA or Canada.

(510) 670-0589 

Fax to Customer Service or Tech Support.

www.davisnet.com 

Copies of User Manuals are available on the “Support” page. 

Watch for FAQs and other updates. Subscribe to the e-newsletter.

[email protected]

 E-mail to Technical Support.

[email protected]

 E-mail to Customer Service.

[email protected]

 General e-mail. 

Note: 

Please do not return items to the factory for repair without prior authorization.

Specifications

Temperature range: –40 to 150° Fahrenheit (–40 to 65° Celsius)

Wireless transmission frequency: 902 - 928 MHz 

868.0 - 868.6 MHz FHSS for overseas version – Product # includes “OV”

Transmitter ID codes: 8 user-selectable

License: low power (less than 8 mW), no license required

Primary power input: Solar power – Davis solar charger 

Secondary (backup) power: CR-123A 3-volt lithium battery or optional Vantage 
AC power adapter 

Summary of Contents for Anemometer Transmitter Kit













Reviews: