background image

Product Numbers: 6345, 6345OV

Davis Instruments Part Number: 07395.267
 
Wireless Soil Moisture, Leaf Wetness, Temperature Station 2 Installation Manual 
Rev. B Manual (3/1/05)

This product complies with the essential protection requirements of the EC EMC Directve 89/336. 

3465 Diablo Avenue, Hayward, CA 94545-2778

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected]  •  www.davisnet.com

cable, stripped and tinned

Maximum Cable Length  . . . . . . . . . . . . . . . . . . . . . . 24 AWG: 800’ (244 m), 22 AWG: 

1200’ (365 m)

Wireless Communications

Transmit Frequency

 . . . . . . . . . . . . . . . . . . . . . . . . US Models: 902-928 MHz 

FHSS, Overseas Models: 
868.0 - 868.6 MHz FHSS.

ID Codes Available

. . . . . . . . . . . . . . . . . . . . . . . . . 8

Output Power

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902-928 MHz FHSS: FCC-

certified low power, less than 8 
mW, no license required
868.0 - 868.6 MHz FHSS. 
CE-certified, less than 8 mW, no 
license required

Range

Line of Sight  . . . . . . . . . . . . . . . . . . . . . . . . . . . up to 1000 feet (300 m)
Through Walls . . . . . . . . . . . . . . . . . . . . . . . . . . 200 to 400 feet (75 to 150 m)

FCC Part 15 Class B Registration Warning

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant 
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. However, there is no guarantee that interference will not occur in a particular 
installation. 

If this equipment does cause harmful interference to radio or television      reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved in writing by Davis Instruments may void the user's 
authority to operate this equipment.

Summary of Contents for 6345





















Reviews: