background image

 

 

DaVinci Birch Log Set

 

Installation Instructions

 

(sku#

 

94500977)

 

 

Page 1 of 22 

17602180

 — 8/21/20 

© Travis Industries, Inc.  

Compatibility 

  All DaVinci Fireplaces 

Overview 

This log set supplies everything needed to install in all 

CAT1

 fireplaces (2’, 3’, 4’, and 5’, lengths).  

For CAT2+ fireplaces

purchase one additional log set kit for every additional 5’ or less of length.  

 

Example

18’ DaVinci would use four log set kits (3 kits for the first 15’ using the 5’ setup for each, and one additional kit using the 3’ 
templates and setup).   

NOTE:

 For 2’, 3’, 4’ foot lengths not all of the included logs and stones are used.  Unused logs and stones may be discarded. 

 

Table of Contents 

Compatibility

 

...........................................................................................................................................................................

 

1

 

Overview

 

.................................................................................................................................................................................

 

1

 

Packing

 

List

 

..............................................................................................................................................................................

 

2

 

Templates

 

...............................................................................................................................................................................

 

3

 

Tools

 

Required

 

........................................................................................................................................................................

 

3

 

Installation

 

Notes

 

....................................................................................................................................................................

 

3

 

2’

 

Fireplace

 

..............................................................................................................................................................................

 

4

 

2’

 

Fireplace

 ‐ 

Preparing

 

the

 

Media

 

Tray

 

..............................

 

4

 

2’

 

Fireplace

 ‐ 

Overview:

 

......................................................

 

4

 

2’

 

Fireplace

 ‐ 

Log

 

Installation

 

..............................................

 

5

 

3’

 

Fireplace

 

..............................................................................................................................................................................

 

8

 

3’

 

Fireplace

 ‐ 

Preparing

 

the

 

Media

 

Tray

 

..............................

 

8

 

3’

 

Fireplace

 ‐ 

Overview:

 

......................................................

 

8

 

3’

 

Fireplace

 ‐ 

Log

 

Installation

 

..............................................

 

9

 

4’

 

Fireplace

 

..............................................................................................................................................................................

 

12

 

4’

 

Fireplace

 ‐ 

Preparing

 

the

 

Media

 

Tray

 

..............................

 

12

 

4’

 

Fireplace

 ‐ 

Overview:

 

......................................................

 

12

 

4’

 

Fireplace

 ‐ 

Log

 

Installation

 

..............................................

 

13

 

5’

 

Fireplace

 

..............................................................................................................................................................................

 

17

 

5’

 

Fireplace

 ‐ 

Preparing

 

the

 

Media

 

Tray

 

..............................

 

17

 

5’

 

Fireplace

 ‐ 

Overview:

 

......................................................

 

17

 

5’

 

Fireplace

 ‐ 

Log

 

Installation

 

..............................................

 

18

 

Replacement

 

Part

 

Numbers

 

....................................................................................................................................................

 

22

 

 

 

 

Summary of Contents for 94500977























Reviews: