background image

SETTING UP AND OPERATING INSTRUCTIONS

AND PARTS LIST FOR

DAVID BRADLEY

GARDEN TRACTOR

ROTARY SNOWPLOW

917.57587

The above number is the Model Number of your David
Bradley Garden Tractor Rotary Snowplow. It will be
found on a plate attached to the right rear corner of
the Scoop. Always mention the Model Number of your
Rotary Snowplow when communicating with us.

All parts listed herein may be ordered through Sears,
Roebuck and Co. or Simpsons-Sears Limited. When
ordering parts by mail from the mail order house
which serves the territory in which you live, selling
prices will be furnished on request or parts will be
shipped at prevailing prices and you will be billed
accordingly.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE
THE FOLLOWING INFORMATION AS SHOWN IN THIS
LIST:

1.

The PART NUMBER.

2.

The PART NAME.

3.

The MODEL NUMBER.

4.

The NAME of Implement.

This list is valuable. It will assure your being able
to obtain proper parts service at all times. We sug-
gest you keep it with other valuable papers.

SEARS, ROEBUCK AND CO. U.S.A.
SIMPSONS-SEARS LIMITED CANADA

Printed in U.S.A.

MODEL NUMBER

HOW TO ORDER REPAIR PARTS

Summary of Contents for 917.57587









Reviews: