background image

DM9163 

                                                                                                                    Layout  Guide

 

Version: DM9163-LG-V10 

 

May 5, 2014 

 

 

  It is recommended that RX

±

  receive and TX

±

  transmit traces turn at 45

°

 angle. Do not turn at right angle. 

 

       

B e tt e r

W o r s e

 

 

  Avoid using vias in routing the traces of RX

±

  pair and TX

±

 pair. 

 The 

RX

±

 pair, TX

±

  pair, clock, should be routed to have characteristic impedance of 50 Ohm. 

  Do not place the DM9163 RX

±

 receive pair across the TX

±

 transmit pair. Keep the receive pair away from 

the transmit pair (no less than 3mm). It’s better to place ground plane between these two pairs of traces. 

  Do not route any digital signal between the DM9163 RX

±

 and TX

±

 pairs to the RJ-45. Keep the two pairs 

away from all the other active signals and the chassis ground. 

  There should be no power or ground plane in the area under the network side of the 10/100M magnetic and 

the area under the RJ-45 connector. 

  Any terminated pins of the RJ-45 connector (pins 4,5,7 and 8, see Figure 1-1, 1-2) and the magnetic (see 

Figure 1-1, 1-2) should be tied as closely as possible to the chassis ground through a resistor divider network 
75

Ω

  resistors (no more than 2mm to the magnetic) and a 0.1

μ

F/2KV bypass capacitor. 

 

The Band Gap resistor should be placed as close as possible to pins 47 and 48 (BGRES, BGRESG) (no 
more than 3mm). Avoid running any high-speed signal near the Band Gap resistor placement (no less than 
3mm from 25MHz XT1 and XT2).

 

 

Summary of Contents for DM9163











Reviews: