manualshive.com logo in svg

Davicom DM562AP, Operation Manual

Share
Download
Davicom DM562AP Operation Manual Download Page 29

DM562AP

Operation Manual & AT Command Set

Integrated Data/Fax/Voice/Speakerphone Modem

Preliminary

29

Version: DM562AP-MA-P01
February 2, 2004

Turn the system off and on. Go to terminal mode,
issue "AT&FZ". The response should be OK.

•

  The modem does not answer incoming calls

automatically.

Type ATS0? and the response should not be 0. If it
is, the auto answer function is disabled. To turn it
back on, type ATS0=1.

•

  The modem will not dial out.

Use a telephone and insert the jack into the modem
PHONE jack, lift the receiver. If there is no tone, the
line connection is need to be checked. If there is a
tone, but not normal dial tone, turn system off and
on, and try again.

•

  The modem dials, but not connect.

 
 Type AT&FZ, and re-dial the number, if there are no

modem negotiation sound from the modem, the
remote side is not a modem.

 Try AT+FCLASS=0, and AT#CLS=0 to put modem back

to data mode.

 
If you go through the possible process and the problem
is still there, it is time to call your dealer to discuss the
problem. 

But do not call your dealer before you try

first

. The customer services personnel will ask you for

the detailed information. The more information you
provide the better chance your problem can be s

olved.

Summary of Contents for DM562AP






























Reviews:

No comments

Brands by name

Popular brands

Load more brands