background image

FUEL PRO

®

 483

TECHNICAL MANUAL

T e c h n o l o g y ,   L L C

19

DAVCO Technology, LLC       P. O. Box 487        Saline, MI  48176         800-328-2611      www.davco.com     F1305 REV F

Parts Return General Policy

Note: 

A Return Goods Authorization (RGA) must be obtained from DAVCO prior to returning any products . Returns may be 

accepted under the following circumstances: 
Order Shipping Error: A credit against the original invoice, including freight charges for both ways will be issued for returns 
in which DAVCO inadvertently shipped incorrect quantity or product . 
Overstock: Returns for ordering more product(s) than required, or incorrect part(s), will be accepted within 60 days from 
the date of purchase . Proof of purchase will be required, i .e .: original invoice/delivery receipt . These types of return(s) are 
subject to a minimum restock fee of 40% or $40 .00, whichever is higher . Additional restock fees may apply . Product(s) will 
be inspected for “like new” condition and additional costs will be the responsibility of the customer . No obsolete parts may 
be returned . 
Freight charges for return(s) will be the responsibility of the customer .

PARTS RETURN POLICY

Summary of Contents for FUEL PRO 483






















Reviews: