Via monte Nero, 40/B – 21049 TRADATE (VA) ITALY
Phone: +39 (0)331841070 Fax:+39 (0)331841950 - e-mail:
DAT 4532 C
DAT 4532 C
Isolated, double channel
converter for PTC/NTC/Pot
configurable by Dip-Switch or PC
FEATURES
- Configurable input for PTC, NTC and Pot.
- Configurable output in current or voltage
- Double channel in the same enclosure
- Configurable by dip-switch or PC
- High accuracy
- On-field reconfigurable
- Galvanic isolation among the ways
- EMC compliant – CE mark
- Suitable for DIN rail mounting in compliance
with EN-50022 and EN-50035
GENERAL DESCRIPTION
The isolated double channel converter DAT 4532 C is able to measure and linearise the standard PTC and NTC sensors and potentiometers. In function
of programming, the measured values are converted in a current or voltage signal. The device guarantees high accuracy and performances stability both
versus time and temperature.
The double channel allows the high density mounting where is necessary to reduce the encumbrances.
The programming is made by the dip-switch located in the window on the side of the enclosure. By means of dip-switches it is possible to select the input
type and range and the output type without recalibrate the device.
Moreover, by Personal Computer the user can program all of the device's parameters for his own necessity; the configuration by PC allows to program
the two channels with two independent settings.
Moreover it is available the option of alarm for signal interruption (burn-out) that allows to set the output value as high or low out of scale .
The 1500 Vac galvanic isolation on all ways (inputs, outputs and power supply) eliminates the effects of all ground loops eventually existing and allows
the use of the converter in heavy environmental conditions found in industrial applications.
The DAT 4532 C is in compliance with the Directive 2004/108/EC on the Electromagnetic Compatibility.
It is housed in a plastic enclosure of 12.5 mm thickness suitable for DIN rail mounting in compliance with EN-50022 and EN-50035 standards.
USER INSTRUCTIONS
The converter must be powered by a direct voltage applied to the terminals Q and R.
The channel A measures the value from the sensor connected to the terminals I, L and G and transmits the output measure on the terminals N and M.
The channel B measures the value from the sensor connected to the terminals E, F and H and transmits the output measure on the terminals P and O.
The input and output connections must be made as shown in the section "Connections".
It is possible to configure the converter on field by dip-switch or Personal Computer as shown in the section “ Programming ". The configuration by
dip-switches can be made also if the device is powered (note: after the configuration the device takes some seconds to provide the right output measure ).
TECHNICAL SPECIFICATIONS (Typical at 25 °C and in nominal conditions)
Sensor excitation current
PTC, NTC
500 uA
Linearity
(1)
PTC, NTC ± 0.1 % f.s.
Thermal drift
(1)
Full scale
± 0.01% / °C
TEMPERATURE AND HUMIDITY
Operative temperature
-20°C .. +60°C
Storage temperature -40°C.. +85°C
Humidity (not condensed)
0 .. 90 %
Output type
Min
Max
Min Span
HOUSING
Material Self-extinguishing plastic
Mounting DIN rail in compliance
with EN-50022 and
EN-50035
Weight
about 90 g.
Output calibration
Current
± 7 uA
Voltage
± 5 mV
Power supply voltage
18 .. 30 Vdc
Reverse polarity protection
60 Vdc max
EMC ( for industrial environments )
Immunity
EN 61000-6-2
Emission
EN 61000-6-4
Current consumption
Current output
55 mA max.
Voltage output
25 mA max.
Burn-out values
Max. output value
22 mA or 10.6 V
Min. output value
0 mA or -0.6 V
Current
0 mA
20 mA
4 mA
Voltage
0 V
10 V
1 V
(1)referred to the input Span (difference between max. and min.)
Response time
(10÷ 90%)
about
500 ms
Output load Resistance - Rload
Current output
< 500
Ω
Voltage output
> 10 K
Ω
Short circuit current 26 mA max.
ISOLATION
Among all ways
1500 Vac,
50 Hz, 1 min
POWER SUPPLY
INPUT (2 channels)
OUTPUT(2 channels)
Input Calibration
(1)
PTC, NTC the higher of ±0.1% and ±0.2°C
Potentiometer ± 0.05 % f.s.
Input type
Min
Max
Min.Span
PTC
KTY81-210
-55°C
150°C
50°C
KTY81-220
-55°C
150°C
50°C
KTY84-130
-40°C
300°C
50°C
KTY84-150
-40°C
300°C
50°C
Pot.
(Rnom.< 50K
Ω
)
0
%
100
%
10
%
NTC
Coster 10K
-10°C
100°C
50°C
Coster 1K
-30°C
40°C
25°C
NTC
PTC Pot
V
mA
V
mA
DC SUPPLY
INPUT A
OUTPUT A
+
-
INPUT B
OUTPUT B
NTC
PTC Pot
