manualshive.com logo in svg

Datavideo NVS-10, Instruction Manual

Share
Download
Datavideo NVS-10 Instruction Manual Download Page 18

 

17

System Setup 

Read this section to learn about the System menu settings and options. 

System Setting 

Click on the System menu title or tab to access the system configuration screen below: 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
This displays all system information, including firmware version, Upnp, device name and also allows you to 

upgrade the firmware of your unit should you need to. 

 

In 

Device Name

, you can type in a new name for the NVS-10 and click the apply button to change the 

device name. The current NVS-10 firmware version is also displayed below this Device Name.  

 
 
 
 
 
 
 

Please leave the 

Upnp Service

 enabled so that it is always on. 

 
 
 
 

 
In Utilities section, you can reset to 

factory defaults

 or 

remotely reboot

 and allow 

firmware upgrade

. 

Under Reset to Factory Default, click the apply button restore all factory set defaults. 

 
 
 
 
 
 
 
 
 
 

Once selected a confirmation dialogue appears. Click OK if you wish to proceed. 
 
 

Summary of Contents for NVS-10


























Reviews:

No comments

Brands by name

Popular brands

Load more brands