SETTING OF THE 2 THRESHOLDS
The sensor setting is effected placing the object to detect directly in front of the sensor following the
procedure given below:
z
push-button
pressed
{
push-button not pressed
LED
on
LED
off
-
Obect detection at OFF/ON output switching
- Position the object inside the measurement area to define the measurement value (depending
on the operating mode used) corresponding to the OFF/ON switching of the digital output.
Display
Keyboard
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
4
5
0
{
z
{
-
Press the SET push-button for at least 2s.
-
The detected value for the first switching threshold appears (4Hz blinking until the SET push-
button is released).
-
The value acquired can be changed using the +/- push-buttons.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
4
5
0
z
{
z
-
The units change if these push-buttons are pressed repeatedly, the tens if kept pressed.
-
Press the SET push-button again for at least 0.5 s. to end the detection phase of the first
switching threshold.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
4
5
0
{
z
{
-
Obect detection at ON/OFF output switching
- Position the object inside the measurement area to define the measurement value (depending on
the operating mode used) corresponding to the ON/OFF switching of the digital output.
-
The detected value for the second switching threshold appears.
-
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
6
0
0
{
z
{
-
The present value appears (4Hz blinking).
-
Press the SET push-button again for at least 0.5 s. to detect the second switching threshold.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
6
0
0
{
z
{
-
The detected value for the second switching threshold appears.
-
The value acquired can be changed using the +/- push-buttons.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
6
0
0
z
{
z
-
The units change if these push-buttons are pressed repeatedly, the tens if kept pressed.
-
Press the SET push-button again for at least 0.5 s. to end the detection phase.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
6
0
0
{
z
{
SWITCHING THRESHOLD ADJUSTMENT
Display
Keyboard
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
0
4
5
0
z
{
z
-
Press one of the +/- push-buttons for at least 2 s.
-
The “tH-1” message appears.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
t
H
-
1
{
{
{
-
Switching threshold selection
-
Use the +/- push-buttons to select the switching threshold.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
t
H
-
1
z
{
z
t
H
-
2
z
{
z
-
Adjustment phase of the switching threshold
-
Press the SET push-button for at least 0.5 s.
-
The previously detected value appears.
-
The value can be changed using the +/- push-buttons.
-
The units change if these push-buttons are pressed repeatedly, the tens if kept pressed.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
0
6
0
0
z
{
z
-
Press the SET push-button again for at least 0.5 s. to end the adjustment phase.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
0
4
5
0
{
z
{
SETTING OF THE PARAMETERS
Display
Keyboard
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
4
5
0
{
z
{
Press the SET push-button for at least 6s to enter into the parameter setting mode.
The "MEnu" message appears.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
M
E
n
u
{
{
{
-
Pressing the + and –push-buttons the user can run up and down the menu, reading the
following messages.
-
Functioning mode selection
- At each pressure on the SET push-button the user can run through the options of the selected
level.
OUT A M1
M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
E
n
d
z
{
z
b
E
G
{
z
{
c
E
n
t
{
z
{
W
I
d
t
{
z
{
A
r
E
A
{
z
{
-
Delay setting
-
At each pressure on the SET push-button the user can run through the options of the selected
level.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
d
-
0
0
z
{
z
d
-
0
5
{
z
{
d
-
1
0
{
z
{
d
-
2
0
{
z
{
d
-
3
0
{
z
{
d
-
4
0
{
z
{
- The setting of the delay value is in common to both outputs.
When the delay value set is different from zero, the outputs will remain active for a minimum
time equal to the number of milliseconds visualised on the display.
-
Visualisation of the threshold 1 data
-
Pressing the SET push-button the value of the threshold 1 appears.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
t
H
-
1
z
{
z
THRESHOLD
0
4
5
0
{
z
{
-
Visualisation of the threshold 2 data
-
Pressing the SET push-button the value of the threshold 2 appears.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
t
H
-
2
z
{
z
THRESHOLD
6
0
0
{
z
{
-
Visualsation of the operating area status
- Pressing the SET push-button the operating area status. More precisely; if “FULL” the operating
area is complete, if “REDU“ the acquired area is not complete, but presents some zones that do
not have to be detected .
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
F
U
L
L
z
{
z
or
r
E
d
U
z
{
z
-
Reset of the sensor default configuration
-
Pressing the SET push-button (the “RESE” message blinks for 2s, 4Hz) the default configuration
is re-set and the user exits from the menu, returning to the normal mode. The default
configuration is: “beg object” operating mode, delay 0, Th1 switching threshold = 100, Th2 =
200.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
r
E
S
E
z
{
z
r
E
S
E
{
z
{
-
Memorisation of the parameters set
- Pressing the SET push-button (the “SAVE” message blinks for 2s, 4Hz) all the modified values
are memorised and the user exits form the menu,returning to the normal mode.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
S
A
V
E
z
{
z
S
A
V
E
{
z
{
- Press one of the +/- push-buttons the user can return to the setting menu.
-
Exit from the parameter setting menu
After 10s inactivity of the sensor push-buttons, the sensor returns to the normal operating mode
visualising the distance.
ADVANCED FUNCTIONS
Display
Keyboard
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
0
4
5
0
z
{
z
-
Operating area selection
-
Press contemporarily the + and – push-buttons for at least 2s.
-
The “W_Ar” message appears.
OUT A M1 M2 Dig1 Dig2 Dig3 Dig4 +
SET
-
W
_
A
r
{
{
{
W
_
A
r
{
z
{
-
The operating area configuration is memorised when the push-buttons are released (the W_Ar
blinks for 2s, 4Hz) and the sensor returns to the normal mode.
