background image

Bluetooth UHF RFID Reader User Manual 

 

 

 

 

UM001371 

Page 11 / 17 

Rev. 1.0 

 04.12.2019 

 

5.2

 

Change operating mode 

To change the operating mode please follow the steps below. 

1.

 

Connect to thi

link

 to start the 

“Desktop Firmware Loader” 

download and then install it; 

2.

 

Delete existing BT pairings the reader (from your smartphone and/or PC); 

3.

 

Launch the “Desktop Firmware 

L

oader”;

 

4.

 

Connect the reader to the PC using the supplied micro USB cable; 

5.

 

The driver is automatically installed. The loader should prompt as the COM port arrives and select the 

right port automatically (“Port COMn arrived”)

 

Figure 11 - Desktop Firmware Loader setting 

6.

 

Select 

Action -> 

Reset Bluetooth to “xx” mode

, where “x” is the 

operating mode you want to switch to; 

 

Figure 12 - Desktop Firmware Loader setting 

7.

 

Wait until the 

message “Operation Completed” is shown;

 

 

Figure 13 - Desktop Firmware Loader setting 

8.

 

Unplug the micro USB cable; 

9.

 

Pair to the reader on your device as explained in the following chapters. 

Summary of Contents for Textile ID R-PO-UHF-BT


















Reviews: