ETHERNET CONNECTION
The Ethernet cradle drivers are pre-installed on the Lynx and
initiate automatically when the terminal is placed in a properly
connected Four Slot Dock Ethernet.
When the PDA is inserted into the Four Slot Dock Ethernet, the
connectivity icon on the taskbar indicates that the mobile
computer is connected to a network.
NOTE
The maximum bandwidth capacity for each
device is 12Mbps.
The yellow Link LED blinks to indicate activity, or stays lit to
indicate that a link is established. When it is not lit it indicates
that there is no link.
CAUTION
Connections should always be made with power
OFF!
How to connect
Connect the Ethernet cradle (Ethernet port 1 - E) to an Ethernet hub
or to a port on the host device. Connect the Ethernet cradle (power
port - F) to the power supply.
Figure 6 - Ethernet Connection
Key:
A)
Ethernet 4 Slot Dock
B)
Power supply without power cord, supplied with the 4SD
and country specific power cord
C)
UTP CAT 5E cable (recommended use)
D) Ethernet
hub
E)
Ethernet port 1
F) Power
port
Available in the Ethernet Four Slot Dock only
Daisychaining Ethernet Connection
To connect several cradles to an Ethernet network, the Ethernet
cradles may be daisychained. It is recommended not to connect
more than four cradles in order to maintain the optimal baud rate.
Connect the first Ethernet cradle to the Ethernet Switch. Connect the
additional cradles as shown in Figure 7.
Figure 7 - Daisychaining Ethernet Connection
Key:
A)
Power supply without power cord, supplied with the 4SD
and country specific power cord
B) Ethernet
hub
C)
UTP CAT 5E cable (recommended use)
D) Ethernet Port 1
E)
Ethernet Port 2
WARNING
This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
TECHNICAL FEATURES
Electrical Features
Power supply *
12 VDC ± 5% @ 5A
Consumption
Max 5 A
Spare slot charge time
Std Battery
2h 30
High Cap Battery
4h
Communication Features
Interface Ethernet
**
Baud Rate
10/100BASE-T
Physical Features
Dimensions
445 x 135 x 102 mm
17.5 x 5,3 x 4 in
Weight (without
connection cables)
1250 g / 44.1 oz
Indicators
Green power-on LED
Bicolored battery charge status LED
Environmental Features
Working
temperature***
0° to +50°C / +32° to +122°F ***
Storage temperature
-20° to +70°C / -4° to +158°F
Humidity
95% without condensation
Electrostatic discharge
EN 61000-4-2
4 KV contact / 8 KV air
*
Use only DL approved power adapters.
**
Available in the Ethernet Four Slot Dock only
*** When inserted in the spare slot, batteries must be charged at a
temperature ranging from 0° to 44 °C.
Never charge the main device or spare batteries in a closed space
where excessive heat can build up.
FCC COMPLIANCE
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Modifications or changes to this equipment without the
expressed written approval of Datalogic could void the authority
to use the equipment.
This device complies with PART 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference which may cause
undesired operation.
E
A
B
A
C
D
A
B
C
D
E
F
